Flagsticks & Flagstick Accessories
Don’t have your staff spend valuable time painting and repainting flag poles when you can VinylGuard them in minutes. Labor is precious–VinyGuard is affordable and helps save time.
Request More Information
"*" indicates required fields
Regulation Flagsticks
How to VinylGuard Your Regulation Flagsticks
- Cut a length of vinyl 3″ longer than the flagstick, to allow for longitudinal shrinkage.
- Begin shrinking at the bottom of the flagstick. Push the material downward, pressing the vinyl against the ferrule until it shrinks to form a snug fit. Then shrink your way up the shaft.
Changing the Color of Flagsticks
- For all colors except yellow: slide on a new color and shrink.
- To change a color to yellow: to ensure complete coverage, first shrink on a base of white vinyl. Slide yellow VinylGuard over the white and shrink.
Tapered Tournament Flagsticks
- Lightly coat the shaft with soapy water. Slide the vinyl over the shaft, pushing the material down as far as possible.
- Begin shrinking at the widest point – in the center of the flagstick. SLOWLY work your way downward, pushing the vinyl against the ferrule until it shrinks to form a snug fit. Return to the center of the flagstick and work your way upward to the top.
- While shrinking, if air bubbles get trapped under the vinyl, press them out with your hand while the vinyl is still warm.
Laser Link Smartsticks™
Laser Link Renewal Kits fit the 1/2″ regulation and older 3/4″ tapered tournament SmartSticks™ with the wide-diameter aluminum reflective prism devices installed in the body of the flagsticks™.
Due to the wide diameter of the aluminum reflective prism device, VinylGuard will be installed in three pieces. The ferrules must be removed and reinstalled or replaced. Ferrules are sold separately.
Shrink VinylGuard over the bottom part of the flagstick:
- Remove the ferrule.
- Cut a length of VinylGuard to cover the lower part of the flagstick, from the bottom to the start of the embedded Laser Link device.
- Slide the VinylGuard up the flagstick; press it against the start of the device. Start shrinking here:
- Apply heat to tightly shrink the VinylGuard against the bottom of the device.
- Hold the heat gun downward at a 45° angle; shrink the VinylGuard down to the bottom of the flagstick.
- When fully cool, trim enough VinylGuard from the bottom of the shaft to accommodate a ferrule.
- Install the ferrule.
Shrink VinylGuard over the top part of the flagstick:
- Cut a length of VinylGuard to cover the flagstick, over-lapping the top stud down to the start of the embedded device
- Slide the VinylGuard down the top of the flagstick; press it against the top of the device.
- Apply heat to tightly shrink the VinylGuard against the top of the device.
- Hold the heat gun upward at a 45º angle; shrink the VinylGuard up to the top of the flagstick.
- When fully cool, trim the VinylGuard below the top stud.
Shrink VinylGuard over the embedded Laser Link device:
- Slide a cut piece of VinylGuard down to evenly overlap the top and bottom of the Laser Link device.
- Apply heat to tightly shrink the vinyl.
- Allow the VinylGuard to fully cool to room temperature and harden for about 20 – 30 minutes.
Expose the prisms after the VinylGuard is fully cooled:
- Put the custom hole cutting tool in a drill press or hand drill.
- Place the tool over the indentations of the prisms and lightly cut through the VinylGuard.
- Remove the cut pieces to expose the prisms.
Renew Your Flagsticks With VinylGuard
Use FS-7550 to Renew the New, Slim ¾” Tapered Tournament SmartSticks™ with the Prisms Embedded in the Fiberglass.
How to:
- Follow the directions for Tapered Tournament Flagsticks.
- Follow the directions – #4 above – to expose the prisms after the VinylGuard is fully cooled.
Pink Stakes, Posts and More
Dress up your golf course flagsticks in pink for Ladies’ Days, Mother’s Day, Breast Cancer Awareness Events and Fund Raisers!
- Cut a length of VinylGuard 2″ longer than the stake or post to allow for longitudinal shrinkage at both ends.
- Begin at the center of the shaft and direct the heat outwards towards the ends. Trim the excess.
- Slightly warm the cap (available from VinylGuard) with the heat gun and cover the top of the stake or post.
- Apply a bit more heat and press the cap into place.
Related Products
Wittek golf is now the exclusive distributor of VinylGuard golf products. Please click here to visit their site. For golf product questions and information, contact Wittek at 1-800-869-1800 or [email protected]